Your Plumbing Crash Course: A Necessity for Bathtub Installation
Your Plumbing Crash Course: A Necessity for Bathtub Installation
Blog Article
Just about everyone has got his or her own theory when it comes to A Step-by-Step Guide to Installing a Bathtub.
Setting up a bathtub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old bath tub with a new one is additionally a moderately challenging project. If the old tub is easily available, the job can move rapidly; if you need to open a wall to eliminate the old tub and also position the new bath tub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to vacate the old bathtub as well as set in the new one. Ensure you have certified on your own for the task and fit attempting it. Rather than working with a service provider to take over a halfway-completed project, it is far better to think about employing one prior to you begin. Possibilities are you may require a professional plumber to make tube links.
This article will aid you set up a brand-new tub in your restroom if you have currently bought a new tub as well as do not need to change the arrangement of your previous water system pipelines.
Your devices as well as material checklist ought to make up the following:
Planning for the Setup
First of all, the supporting structure supplied with the bathroom should be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets unit to avoid stress on the tub.
Fit the flexible faucet connectors to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its last position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, then the first thing you should do is separate the water. After doing so, turn on the taps to drain any type of water staying in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the limited access that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, position the tub in the needed position. The wood boards are helpful in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The following goal is to make certain that the tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the bathtub till the spirit level reviews degree.
To set up faucets, fit all-time low of the outermost flexible faucet connector to the proper supply pipeline by making a compression join; after that do the exact same for the various other tap.
Switch on the water system and inspect all joints and new pipework for leakages and also tighten them if required. Load the bath tub and likewise examine the overflow outlet as well as the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as described in the producer's instruction manual. Tiling and also sealing around the bath tub ought to wait up until the bathtub has been used at least when as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin making sure that the washing machines remain in area between the faucet and also the sink. Protect the faucet in position with the manufacturer provided backnut. As soon as the faucet is securely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet connectors. The former kind should be attached to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to crack an inflexible seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, causing issues with wetness as well as possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures and installations. They are sold in tubes and also cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to always fill up the bathtub with water before securing, to allow for the motion experienced when the tub remains in usage. The sealant can break relatively very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily readily available on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very interested by How to Install a Bathtub Yourself and I am assuming you liked our entry. Do you know somebody who is enthusiastic about the subject? Be sure share it. I am grateful for your time. Visit us again soon.
Hot water issue? Call! Report this page